Re: PirateBox is setup and inactive but the USB key is always blinking December 20, 2017 10:27AM |
Registered: 10 years ago Posts: 53 |
# dmesg [ 0.000000] Linux version 3.3.8 (strubel@compute) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Mon Feb 1 20:10:10 CET 2016 [ 0.000000] MyLoader: sysp=2222a3aa, boardp=2a2b2a82, parts=122ab222 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9132 rev 2 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802f92b0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 28964k/32768k available (2241k kernel code, 3804k reserved, 420k data, 216k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79 [ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND [ 0.360000] bio: create slab <bio-0> at 0 [ 0.370000] Switching to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.400000] TCP reno registered [ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] NET: Registered protocol family 1 [ 0.420000] PCI: CLS 0 bytes, default 32 [ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.450000] msgmni has been set to 56 [ 0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.460000] io scheduler noop registered [ 0.470000] io scheduler deadline registered (default) [ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.510000] console [ttyS0] enabled, bootconsole disabled [ 0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80 [ 0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes) [ 0.540000] 5 tp-link partitions found on MTD device spi0.0 [ 0.540000] Creating 5 MTD partitions on "spi0.0": [ 0.550000] 0x000000000000-0x000000020000 : "u-boot" [ 0.560000] 0x000000020000-0x00000010f000 : "kernel" [ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.570000] 0x00000010f000-0x0000007f0000 : "rootfs" [ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.590000] mtd: partition "rootfs" set to be root filesystem [ 0.600000] mtd: partition "rootfs_data" created automatically, ofs=310000, len=4E0000 [ 0.610000] 0x000000310000-0x0000007f0000 : "rootfs_data" [ 0.620000] 0x0000007f0000-0x000000800000 : "art" [ 0.620000] 0x000000020000-0x0000007f0000 : "firmware" [ 0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3 [ 0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK) [ 0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found [ 0.930000] rtl8366rb: probed [ 0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.240000] TCP cubic registered [ 1.250000] NET: Registered protocol family 17 [ 1.250000] Bridge firewalling registered [ 1.260000] 8021q: 802.1Q VLAN Support v1.8 [ 1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.270000] Freeing unused kernel memory: 216k freed [ 3.510000] ar71xx: pll_reg 0xb8050014: 0x1a000000 [ 3.510000] eth0: link up (1000Mbps/Full duplex) [ 3.680000] Registered led device: tp-link:green:usb [ 3.680000] Registered led device: tp-link:green:system [ 3.680000] Registered led device: tp-link:green:qss [ 3.680000] Registered led device: tp-link:green:wlan [ 6.980000] JFFS2 notice: (437) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 12 of xref (0 dead, 2 orphan) found. [ 7.680000] SCSI subsystem initialized [ 7.810000] usbcore: registered new interface driver usbfs [ 7.810000] usbcore: registered new interface driver hub [ 7.820000] usbcore: registered new device driver usb [ 8.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.200000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 8.210000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.240000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.260000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.260000] hub 1-0:1.0: USB hub found [ 8.270000] hub 1-0:1.0: 1 port detected [ 8.280000] Initializing USB Mass Storage driver... [ 8.290000] usbcore: registered new interface driver usb-storage [ 8.300000] USB Mass Storage support registered. [ 8.590000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 8.740000] scsi0 : usb-storage 1-1:1.0 [ 10.380000] scsi 0:0:0:0: Direct-Access TOSHIBA TransMemory 1.00 PQ: 0 ANSI: 4 [ 10.390000] sd 0:0:0:0: [sda] 60549120 512-byte logical blocks: (31.0 GB/28.8 Gi [ 10.400000] sd 0:0:0:0: [sda] Write Protect is off [ 10.410000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00 [ 10.410000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 10.420000] sda: sda1 [ 10.430000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 28.670000] eth0: link down [ 29.250000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 29.250000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 29.430000] cfg80211: Calling CRDA to update world regulatory domain [ 29.430000] cfg80211: World regulatory domain updated: [ 29.440000] cfg80211: DFS Master region: unset [ 29.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 29.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 29.460000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 29.470000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 29.480000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 29.490000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 29.490000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 29.760000] NET: Registered protocol family 10 [ 30.810000] ath: EEPROM regdomain: 0x0 [ 30.810000] ath: EEPROM indicates default country code should be used [ 30.810000] ath: doing EEPROM country->regdmn map search [ 30.810000] ath: country maps to regdmn code: 0x3a [ 30.810000] ath: Country alpha2 being used: US [ 30.810000] ath: Regpair used: 0x3a [ 30.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 30.830000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2 [ 30.840000] cfg80211: Calling CRDA for country: US [ 30.850000] cfg80211: Regulatory domain changed to country: US [ 30.850000] cfg80211: DFS Master region: FCC [ 30.860000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 30.870000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 30.880000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A) [ 30.880000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s) [ 30.890000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 30.900000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 31.330000] loop: module loaded [ 31.380000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 31.540000] nf_conntrack version 0.5.0 (455 buckets, 1820 max) [ 31.800000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 32.050000] batman_adv: B.A.T.M.A.N. advanced 2013.4.0 (compatibility version 14) loaded [ 35.100000] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities [ 35.100000] EXT4-fs (loop0): couldn't mount as ext2 due to feature incompatibilities [ 35.140000] EXT4-fs (loop0): recovery complete [ 35.150000] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 35.290000] EXT4-fs (loop1): couldn't mount as ext3 due to feature incompatibilities [ 35.310000] EXT4-fs (loop1): couldn't mount as ext2 due to feature incompatibilities [ 35.340000] EXT4-fs (loop1): recovery complete [ 35.350000] EXT4-fs (loop1): mounted filesystem with ordered data mode. Opts: (null) [ 36.790000] ar71xx: pll_reg 0xb8050014: 0x1a000000 [ 37.090000] eth0: link up (1000Mbps/Full duplex) [ 37.090000] device eth0.1 entered promiscuous mode [ 37.100000] device eth0 entered promiscuous mode [ 37.110000] br-lan: port 1(eth0.1) entered forwarding state [ 37.110000] br-lan: port 1(eth0.1) entered forwarding state [ 37.790000] ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 39.110000] br-lan: port 1(eth0.1) entered forwarding state [ 44.240000] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 44.240000] device wlan0 entered promiscuous mode [ 44.270000] br-lan: port 2(wlan0) entered forwarding state [ 44.280000] br-lan: port 2(wlan0) entered forwarding state [ 44.280000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 46.280000] br-lan: port 2(wlan0) entered forwarding state [ 47.780000] Adding 32764k swap on /mnt/usb/external_fs/OpenWRT.swap. Priority:-1 extents:1 across:32764k
Re: PirateBox is setup and inactive but the USB key is always blinking December 21, 2017 08:33PM |
Admin Registered: 13 years ago Posts: 4,680 |
Re: PirateBox is setup and inactive but the USB key is always blinking December 22, 2017 09:52AM |
Admin Registered: 13 years ago Posts: 4,680 |
root@ty5Etx2w:/# free total used free shared buffers Mem: 29180 26620 2560 0 4408 -/+ buffers: 22212 6968 Swap: 32764 188 32576 root@ty5Etx2w:/# ps PID USER VSZ STAT COMMAND 1 root 1504 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 5 root 0 SW [kworker/u:0] 6 root 0 SW< [khelper] 63 root 0 SW [sync_supers] 65 root 0 SW [bdi-default] 67 root 0 SW< [kblockd] 96 root 0 SW [kswapd0] 144 root 0 SW [fsnotify_mark] 173 root 0 SW< [ath79-spi] 184 root 0 SW [mtdblock0] 189 root 0 SW [mtdblock1] 194 root 0 SW [mtdblock2] 199 root 0 SW [mtdblock3] 204 root 0 SW [mtdblock4] 209 root 0 SW [mtdblock5] 250 root 0 RW [kworker/0:1] 444 root 0 SWN [jffs2_gcd_mtd3] 474 root 0 SW [khubd] 483 root 0 SW [scsi_eh_0] 484 root 0 SW [usb-storage] 485 root 0 SW [kworker/0:2] 486 root 0 SW [kworker/u:2] 510 root 1504 S init 545 root 0 SW< [cfg80211] 623 root 0 SW< [bat_events] 650 root 1508 S /sbin/syslogd -C16 652 root 1488 S /sbin/klogd 654 root 872 S /sbin/hotplug2 --override --persistent --set-rules-file 663 root 872 S /sbin/ubusd 739 root 0 SW< [loop0] 744 root 0 SW [jbd2/loop0-8] 745 root 0 SW< [ext4-dio-unwrit] 769 root 0 SW< [loop1] 775 root 0 SW [jbd2/loop1-8] 776 root 0 SW< [ext4-dio-unwrit] 783 root 1472 S /sbin/netifd 1284 root 1640 S hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd-ph 1377 root 1500 S /sbin/watchdog -t 5 /dev/watchdog 1496 root 1152 S /usr/sbin/dropbear -P /var/run/dropbear.1.pid -p 22 1507 root 1496 S /usr/sbin/telnetd -l /bin/login.sh 1513 root 1696 S /usr/sbin/dbus-daemon --system 1518 nobody 2168 S avahi-daemon: running [ty5Etx2w_piratebox_lan.local] 1545 nobody 952 S /usr/sbin/dnsmasq -x /var/run/piratebox_dnsmasq.pid -C / 1548 root 936 S radvd -p /opt/piratebox/tmp/radvd.pid -C /opt/piratebox/ 1550 root 936 S radvd -p /opt/piratebox/tmp/radvd.pid -C /opt/piratebox/ 1571 nobody 4152 S /usr/sbin/lighttpd -f /opt/piratebox/conf/lighttpd/light 1572 nobody 15564 S /usr/bin/php-cgi 1595 root 1500 S /usr/sbin/ntpd -n -p 0.openwrt.pool.ntp.org -p 1.openwrt 1596 nobody 15564 S /usr/bin/php-cgi 1597 root 0 SW [flush-7:1] 1598 root 0 SW [flush-8:0] 1600 root 0 SW [flush-7:0] 1603 root 1500 S /bin/ash --login 1614 root 1496 R ps root@ty5Etx2w:/#